99
Long term use, at least one
Temporary, fuck the screws all together
Both. Lose cables are annoying.
I loathe when the stand offs come out with the vga cable!!!!!
Just one on each end.
Both every time but I also haven't used a VGA cable in at least 15 years.
Lucky you lmao
I still see them once every so often
In fact, I went onsite to a customer who wanted a new PC set up because the old one "wouldn't boot". Sure enough the cable was sticking out of the monitor at about a 15deg angle. I pushed the VGA cable in a bit extra hard and it came right back.
I was out of there in about 30min.
I tighten both screws. With an impact driver. And a dab of LocTite for good measure.
Easy there, Satan!
Okay I'll bite the bait. THE TOP ONE‽‽‽ What sick form factor are you using with vertical VGA ports?
You need to rotate your pc case if the VGA port isn’t vertical. The ground pins always need to be on top so all those grounding electrons weigh down the other conductors to make the data flow more quickly.
That's not true. VGA is a horizontal spec with the entire trapezoid housing being the ground contact. The data electrons to one side is due to the earth's axial tilt spinning them into a corner via healing crystals.
Makes total sense must be true
Can confirm.
Source: am grounding electron.
That's when you use the ports placed on the motherboard in a standard verical PC case, meaning the system uses integrated graphics for the visual output instead of deticated videocard. Videocards that are put into MB at 90° are horizontal, right, but in most office setups I handle they are rare nowadays. Videocards are almost exclusively installed when you handle 3d and content rendering in demanding apps, and for office and browser stuff they are too costy after the crypto price hike and in a sanctioned Russia.
Nettops have horizontal motherboards tho.
standard verical PC case
Excuse you! Standard PC cases are horizontal:
Desktop computers that have a vertically standing motherboard.
load more comments
(1 replies)
Haven't plugged in a VGA cable in a long time. As someone else pointed out it depends if it is temporary or long term.. I always screw them in if it is long term
Haven't plugged in a VGA cable in a long time.
Exactly. What have you done to HDMI and DP ports?
DVI is the Gen X of video connectors
VGA is the Boomers and HDMI is the Millenials. Gen-Z is using USB-C.
Nobody likes DisplayPort
DisplayPort is the cool uncle who is happy to mind the kids for free. A lot of people copy his smooth relaxed style and mannerisms without realising.
load more comments
(1 replies)
load more comments
(1 replies)
VGA cables? You mean grappling hooks?
Ever think you got it unscrewed and accidentally yank the standoff from the PCB?
I work in tech support. I haven't done this, but a user I've worked with absolutely has. I have a photo around here somewhere, if I recall correctly he actually ripped the wires out of the cable lmao!
Edit: the picture. Guess it wasn't wires out of the cable hah. 
How in the fuck?
Well that's retro but I used to only screw in the side that's easier to reach because that already secures it while also allowing you to more easily unplug it again.
One if somewhat temporary.
Both if I want 1-2% increase in performance.
That one standoff got loose 12 years ago, so none.
Otherwise, it's all HDMI and DP.
The real answer is the top one fell out a long time ago.
I plugged one in today. I left the screws loose. Ironically I moved it between two computers that couldn't originally do VGA.
I re-organised my leisure desk. My C64 sometimes hooks up to a TFT thanks to my turbo chameleon 64 cartridge.
Today I hooked my C64 up to my CRT instead. I needed that TFT for my Amiga 1200 which has DVI-I out thanks to my indivision flickerfixer. But I have a DVI->VGA adapter to use that same cable.
Hand tight, then torque wrench, 7-inch pounds.
Jesus Christ, both!! 😆 But only finger tight. Sod you bastards who get the screwdrivers out! That's overkill. 😁
Lightly screw in one
And then replace my old shit and not touch anything but HDMI or DP for the last ten years.
Winner winner chicken dinner
Pro tip: It's a lot easier f you twist both knobs at the same time using the same motion as opening a bottle cap.
Who does just one? That's worse than not doing either. Since they're captive screws, doing just one can force the connector to wedge in crooked. I've had issues with tightening one too far before starting the threads on the other. Sometimes you have to go back and forth a couple times
load more comments
(3 replies)
A school computer lab with a bunch of grubby-handed students touching and licking and who knows what to every surface? Yes, VGA cables get screwed down.
I just use HDMI or DP
DP
BBC?
no, BNC
Both
Serial cables. How quaint.
🤦♂️
Video graphics array connector and DB-9 connectors are not the same.
Both, three rotations after the threads catch.
One or none bears the risk of the connector coming out crooked and bending the pins, causing a potential alignment issue on the next connection and bending them further.
If it's for more than a minute I'll screw in VGA and DVI cables
view more: next ›
this post was submitted on 01 Nov 2024
99 points (97.1% liked)
Asklemmy
43733 readers
1444 users here now
A loosely moderated place to ask open-ended questions
If your post meets the following criteria, it's welcome here!
- Open-ended question
- Not offensive: at this point, we do not have the bandwidth to moderate overtly political discussions. Assume best intent and be excellent to each other.
- Not regarding using or support for Lemmy: context, see the list of support communities and tools for finding communities below
- Not ad nauseam inducing: please make sure it is a question that would be new to most members
- An actual topic of discussion
Looking for support?
Looking for a community?
- Lemmyverse: community search
- sub.rehab: maps old subreddits to fediverse options, marks official as such
- !lemmy411@lemmy.ca: a community for finding communities
~Icon~ ~by~ ~@Double_A@discuss.tchncs.de~
founded 5 years ago
MODERATORS