overview for UncleStewart

10

Biqu B1 SKR V1.4 mainboard to SKR MINI E3 V3? (sh.itjust.works)

submitted 2 months ago by UncleStewart@sh.itjust.works to c/3dprinting@lemmy.world

10 comments fedilink

Has anyone here changed the Biqu B1 SKR v1.4 mainboard to SKR MINI E3 V3?

[Release][v1.40.2] DMs redesign in c/summit@lemmy.world

[-] UncleStewart@sh.itjust.works 3 points 2 months ago

Not sure if only on my android phone, but in messages, all pictures are gone. Just a written link instead of showing actual pictures.
Great work BTW. Looking very nice.

Avatar 3 is officially titled "Avatar: Fire and Ash" in c/movies@lemm.ee

[-] UncleStewart@sh.itjust.works 5 points 2 months ago

And the "Fire and Ash" = spoiler.
I know where this is going..

Biqu B1 - Not heating the hotend in c/3dprinting@lemmy.world

[-] UncleStewart@sh.itjust.works 3 points 2 months ago

I'm a totally noob in the 3D printing scene. My brother has a Biqu B1 and I've printed some small things on his printer. Found a used Biqu B1 for sale for about $80. Yeah, not good research from my side... But, I've printed a well printed fucktopus before it died...

29

Biqu B1 - Not heating the hotend (sh.itjust.works)

submitted 2 months ago by UncleStewart@sh.itjust.works to c/3dprinting@lemmy.world

39 comments fedilink

Hi

A couple of days ago the hotend wouldn't heat up and i got a couple of errorcodes/warnings in the display. The bed heats up just fine, so i ordered a new hotend parts (heater, thermistor and a new aluminum block). Changed all of this, but still the same error. I can se that the thermistor works because it changes values in the display when touching the thermistor-end. Any good ideas why the heater doesn't heat?

6

Noob with a Biqu B1 and BLTouch (sh.itjust.works)

submitted 3 months ago by UncleStewart@sh.itjust.works to c/3dprinting@lemmy.world

6 comments fedilink

Hi

I've bought myself a used Biqu B1 with a BLTouch for a fair price. The seller said that he never got the BLTouch working. Now I`m trying to get the auto leveling to work, but every tutorial and video shows the ABL option in the menu, but i do not have that option. The BLTouch is connected as every video and instruction manual shows, the sensor has flipped down a couple of times so that too is working, and the red led-light i always on. Other menu-guides shown in different internet tutorials also shows minor menu variations from my printer.

Some useful info: System: Marlin 2.1.1 Board: Bigtreetech_TFT35_B1_V3.0 Firmware: TFT35_B1_V3.0.26.x Me: Complete noob with no knowledge of 3D printing lingo

What should be done to get the ABL option in my menu?

I'm a dad of two girls. in c/fatherverse@midwest.social

[-] UncleStewart@sh.itjust.works 10 points 4 months ago

I have 3 daughters, and my nail polished toenails lasted for 11 months...

Posts aren't marked as read on secondary account in c/syncforlemmy@lemmy.world

[-] UncleStewart@sh.itjust.works 3 points 4 months ago

I have Sync and 7 others installed, and I'm only using Sync just because of these small missing things.. It would probably be better if I ranted in their sub's.

Posts aren't marked as read on secondary account in c/syncforlemmy@lemmy.world

[-] UncleStewart@sh.itjust.works 8 points 4 months ago

None of the others has "hold to preview" pictures. And none scrolls as smooth..

Fresno homeowner starts fire trying to kill spider in c/nottheonion@lemmy.world

[-] UncleStewart@sh.itjust.works 2 points 5 months ago

Are there any EV cars without any "technology"? in c/asklemmy@lemmy.ml

[-] UncleStewart@sh.itjust.works 10 points 5 months ago

Had a 1998 Citroen Electrique once. Not much fancy electronics there..

14

Openvpn / pihole - change administration link (sh.itjust.works)

submitted 6 months ago by UncleStewart@sh.itjust.works to c/selfhosted@lemmy.world

4 comments fedilink

Hi So, I've had openvpn running on a raspberry pi for over a year with no problems. After some braining I concluded that I also should run pihole on the same raspberry pi. After all it's "just a DNS resolver". Both are running great together on the raspberry. But, I can't administer openvpn because they both use "/admin", and because I installed pihole last, well I can now only administer pihole. So, how do I make one of them use something like "/admin2" ?

Thanks

Hot take in c/linuxmemes@lemmy.world

[-] UncleStewart@sh.itjust.works 10 points 9 months ago

Haha, true. Started with Mint, now on Kubuntu. Same pig, different makeup.

DOJ sues eBay for selling ‘rolling coal’ devices; fines could hit $2 billion in c/climate@slrpnk.net

[-] UncleStewart@sh.itjust.works 5 points 1 year ago

I approve of this

Finally safe in c/lemmyshitpost@lemmy.world

[-] UncleStewart@sh.itjust.works 3 points 1 year ago

This now just works as a massive antenna..

Rare but nobody cares: 1991 Peugeot 106 Electric. A factory EV option in the late 90s in c/cars@lemmy.world

[-] UncleStewart@sh.itjust.works 5 points 1 year ago

I had a Citroen Saxo Electrique 1998 model. I don't know how to express my experience with the car other than interesting and french, with a touch of PTSD because you'd never know how far you get.