Hi, I have printed a small holder for a Bowden tube to print from my filament dryer outside of the enclosure, but the filament coming out of the tube is tensioned and I don’t know if it will cause problems later. Is this fine to keep or how can I fix this? This i a Ender 3 V3 SE btw.
I'll say that it can lead to uneven extrusion and even skipped steps on your extruder. How much, and how much that amount matters is entirely dependant on the setup and your workflow.
There are a few 3D printed solutions to keep filament tension neutral using a buffer system. It's not a bad idea to check out some of them.
Yes, that will cause problems. Don’t attach it to the frame. Attach it directly to the toolhead.
I think you saw what I saw. The tensioned Bowden tube going from the tool head to the frame. While that might be a problem I think he asked about something else. I only caught that after reading the other comments. But correct me if I am wrong :)
In the picture is no tube going to the toolhead. The white line you see is the filament. The Bowden tube is only connected to the frame. That means that every time the toolhead moves to either side, it will tug on the filament. potentially creating artifacts in the print and maybe even causing underextrusion and slipping extruder gears.
I stand corrected, sorry!
That should be fine, I've printed tens of kilograms pulling the filament around a sharp corner. As long as it's dry, pla can handle quite a bit of abuse. And it's unlikely to damage your printer or dryer.
In the worse case you might have some dust buildup, keep it clean
Re: dry. I'm convinced PLA doesn't care about moisture. Watched a video of a guy that soaked a roll in a tub of water overnight, then printed off the roll with it still in the tub. Looked exactly the same as it did before the soak.
Mileage may vary of course but ever since then I've been leaving my PLA out and it's never once given me trouble (the infused ones a little bit).
I've had filament sit for months before it started getting brittle. But it does get very brittle. At least the stuff I have bought so far has
What type of a spool holder you have in the dryer? It might be a good idea to get some bearings in there to help the spool spin as freely as possible.
Recommend this. Have a similar setup and you can 3d print spools and order bearings for them. That being said my direct drive filament feeder on my prusa is quite strong. As long as you make smooth curves with your bowden tube it should be ok.
It comes with 2 spinning tubes so it does spin freely
It might. Depending on how much tension there is. Too much and it will cause the filament to slip in the extruder causing under extrusion. If you are not seeing signs of under extrusion then you are fine for now - but that might change if you change filament or anything else. I would try to lower how much tension the filament is under to avoid problems in the future. Otherwise it would be something to keep in mind if you do start seeing signs of under extrusion.
But how do I lower the tension? I think its just the friction in the tube.
It could be a tight bend in the line somewhere - make sure there are no tight bends. Otherwise if it is the tube then get a thicker tube.
3DPrinting is a place where makers of all skill levels and walks of life can learn about and discuss 3D printing and development of 3D printed parts and devices.
The r/functionalprint community is now located at: !functionalprint@kbin.social or !functionalprint@fedia.io
There are CAD communities available at: !cad@lemmy.world or !freecad@lemmy.ml
No bigotry - including racism, sexism, ableism, homophobia, transphobia, or xenophobia. Code of Conduct.
Be respectful, especially when disagreeing. Everyone should feel welcome here.
No porn (NSFW prints are acceptable but must be marked NSFW)
No Ads / Spamming / Guerrilla Marketing
Do not create links to reddit
If you see an issue please flag it
No guns
No injury gore posts
If you need an easy way to host pictures, https://catbox.moe may be an option. Be ethical about what you post and donate if you are able or use this a lot. It is just an individual hosting content, not a company. The image embedding syntax for Lemmy is 
Moderation policy: Light, mostly invisible