Yeah if it came to that I would, but I'd like a not elegant repair first.
Looks aren't an issue, but I feel like I'd feel that lump of polish
hereiamagain
joined 1 month ago
Thanks for the recommendations!
Very cool looking, I will consider this thank you! I had no idea
I recently learned what that means from perusing this community haha
Holy cow thanks for all this extremely specific instruction! I will look into it and report back!
This is a lightweight wool shirt, smartwool brand. I think it's 90 or 100 percent wool, I forgot to photograph the tag.
I use it as a base layer while camping, so looks aren't that important, but I don't want it to fall apart.
I got a couple of snags on my last trip, and I poked most of them back in without issue, these two were bigger and I tried stretching the fabric slightly to pull them in. I did it gently, but they both broke 🫠
Should I use a patch? Or sew a few loose stitches to hold things together? Or just leave it alone?
The underside of the shirt is bright orange, the hole is only the top layer, if that makes sense?
Thanks!
Yep. And for me, it changed. I played fps on controller my whole childhood, I was always standard. I started playing less controller and more mouse and keyboard as I got older.
A few years ago I started flying fpv drones.
Recently tried to use a controller again? Whoops I can only play inverted now 🤷♂️
No worries thanks for the information!
That's good to know thanks!
Good to know, I'll have to play with it.
Ah that makes sense haha
I loved this glass bed. After so much time trying to get anything to stick to the stock ender 3 bed, this glass bed has things sticking almost TOO well.
It was fine enough for PLA, but I've been playing with PETG lately and it sticks a little harder.
Well today I printed the entire bed flat for a little hiking table I'm experimenting with.. and this happened when I tried to get it off...
Suggestions for replacement? Should I go glass again? I don't have bltouch so I like how flat glass is, set it and forget it. But I've seen those magnetic plates that allow for super easy removal but just flexing the plate, but this bed is aluminum I think. Plus that seems similar to the stock ender 3 plate that I despise.
29
[not solved, but worked around] Tinkercad not exporting holes? They don't even show up in the preview. Some of my previously working designs are also doing this.
(sh.itjust.works)
I made this test block to test the fit on some holes (my printer isn't calibrated), when I noticed the problem. The cone on the side was a sanity check for this problem.
I tried googling but couldn't come up with this same problem.
Edit: I did just figure out a way, I made them a union group, which applied the cuts immediately, and they stayed when exported. I’ve never had to do that before. Though admittedly that's probably the right way, I normally use fusion360. Something is definitely weird though. It should just work without doing that. And in fact it did a few days ago on a different project file.
229
I upgraded my LCD to OLED with DeckSight! Also swapped the case and buttons while I was at it
(sh.itjust.works)
The screen swap was easy peasy, the hardest part was getting the old screen out. Mine was already broken, and I wasn't keeping the front plastic, so I didn't have to worry about being too careful, except around the top edge where the mics and ambient light sensor are.
The case swap was a bear, took forever. I'm fairly handy, but the whole process took almost 4 hours. My buddy was doing his in tandem with me and he was over 5 hours, and that's with me lending a hand towards the end.
It looks great, in my opinion, and I'd do it again, I'd just start earlier in the day 😬
As far as the OLED goes, so far it looks good. The stock brightness slider isn't working, it must be a software thing? I have had zero time to look into it. I haven't even played a single game on it since doing the swap. I'll report back when I have time to give it a fair shake.
view more: next ›
What was it? Op deleted his comment