this post was submitted on 23 Aug 2023
8 points (100.0% liked)

Self Hosted - Self-hosting your services.

11587 readers
29 users here now

A place to share alternatives to popular online services that can be self-hosted without giving up privacy or locking you into a service you don't control.

Rules

Important

Beginning of January 1st 2024 this rule WILL be enforced. Posts that are not tagged will be warned and if not fixed within 24h then removed!

Cross-posting

If you see a rule-breaker please DM the mods!

founded 3 years ago
MODERATORS
Zoe8338@lemmy.ml
dogmuffins@lemmy.ml
testman@lemmy.ml
8
Looking for router recommendations with SFP ports (sh.itjust.works)
submitted 1 year ago by themoonisacheese@sh.itjust.works to c/selfhost@lemmy.ml
5 comments fedilink hide all child comments
 

hey all, i'm looking to replace my isp's router (i know that i can, it's basically just DHCP on a specific VLAN) with my own one and i'm looking for recommendations.

here's what i would need out of it:

  • best price-to-performance ratio. the larger the NAT table it can keep in RAM the better (i run some things akin to ipv4 scanning)
  • OpenWRT support
  • at least one sfp port for internet access, supporting 5Gb/s.
  • at least one 1 Gb/s ethernet port
  • ideally 2-3 100Mb/s ethernet ports
  • wifi support: yes (don't need anything fancy, even 5GHz is optionnal but preffered)
  • LTE modem: dont care but nice to have

i had a look around the OpenWRT supported devices table but since it doesn't really list ports and i need sfp, it takes a long time to go through and read german router pages.

can anyone recommend a router that meets these at least partially?

you are viewing a single comment's thread
view the rest of the comments
[โ€“] themoonisacheese@sh.itjust.works 1 points 1 year ago (1 children)

Looks really solid. 2.5Gb/s is not a deal breaker, maybe I'll just go back to a lower plan since the only use I get out of it is avoiding network congestion between me and my server downloading at the same time over 2.5Gb links. Thanks for the suggestion!

[โ€“] Malcolm@lemmy.world 3 points 1 year ago

Wow, I'm jealous you live somewhere that you can downgrade to 2.5Gb/s!

If you go that Banana Pi route, just be aware that the process of getting mainline OpenWrt on the thing is a little unusual, but not difficult at all. Just requires a cheap serial adapter and spare micro sd card.

There device has onboard NAND, NOR, and EMMC, as well as the card reader. Not all can be used simultaneously, so there are dip switches that set what is booted/visible.

Official install method is basically as follows:

-Hook up serial adapter to the send/receive/ground pins on the board, open serial terminal in something like PuTTY

-Set dip switches, boot the sd-card

-In serial terminal select option to install to NAND

-Power off, change dip switches, boot to NAND

-In serial terminal select option to install to eMMC

-Power off, change dip switches

-You're done, now booting mainline on eMMC

Basically just putting the image on the NAND memory temporarily so it can be put back on eMMC since eMMC and sd-card can't be used at the same time.

The Banana Pi forums are a good resource in addition to the OpenWRT docs.

My only gripe at this point is that the mainline configuration by default only sets up a 100mb partition on the eMMC to install packages to. Some folks have had success resizing that partition but I wasn't having any luck there, so I may just compile it myself and set it larger. That change should be persistent through system upgrades after it's done once.

Anyway, if you or someone reading this goes that route, I hope this helps!